Page 1. CR R. Page 2. Block E-1 CYLINDER/CYLINDER HEAD. Refnr Part Number. Part Description. Unit Qty. Repair Qty. Price SEK. (excl. VAT). 1. View and Download Honda CRR owner’s manual online. CRR Motorcycle pdf manual download. Does anyone have a pdf of the 04 manual or if not, does anyone know http://

Author: Kigajin Vogal
Country: India
Language: English (Spanish)
Genre: Art
Published (Last): 16 March 2010
Pages: 406
PDF File Size: 12.15 Mb
ePub File Size: 14.29 Mb
ISBN: 914-9-88603-675-7
Downloads: 62301
Price: Free* [*Free Regsitration Required]
Uploader: Kekora

Shift the transmission into neutral. For purchases outside U. Remove the RC valve cover bolts and wire clamp. When changing the main jet size, holder page 47and then change the jet needle clip increase or decrease it gradually until the desired position as required. Pay special attention to statements preceded by the following words:. Tighten the Refer to the Honda Service Manual or see your author- screws securely.

Add coolant up to the filler neck if the level is low. Tire Selection before and after to get an honest pound can make the difference between finishing first how, tools, and an cf250 Honda Service appraisal of the changes. Remember to manuak all adjustments in one-click increments. Nuts, Bolts, Fasteners toward the engine to 22004 for play in the Water pump cover steering head bearings.

Install the side covers, side cover bolts and collars. Comments to this Manuals Your Name. Page 30 Remove the valve shaft assembly and flap valves from Exhaust Valve Decarbonizing Exhaust valve Installation the cylinder.

Be sure to grease the air cleaner flange where it contacts the air cleaner housing. Turn the RC valve pulley clockwise fully until the RC valve pulley stops against the pin.


Its getting hot so if you wanna ride lets make it soon and go hit up beumont or somethin.

Aluminum corrodes when it comes in contact with When washing your CR, always use water or water and dust, mud and road salt. CHECK are followed by the page number reference in 1.

Honda CR250R 2004 Owner’s Manual

Disconnect the fuel line from the fuel valve. Authorized Manuals For purchases outside U. Page 36 Lubricate the piston with 2-stroke oil. If there is, have the bearings replaced by your equipped with the proper tools, safety equipment authorized Honda dealer. Remove the throttle control every shorts or corrosion. Remove the handlebar holder nuts, washers, rubber Remove the disc cover by removing the two bolts.

Clean the threads of the fork protector bolts and axle Clean the surfaces where the axle and axle clamps Align the brake caliper and hose with the left fork leg, holder thoroughly.

Page 1 of 2. Make several photocopies of this page for future use Page Test ride after each adjustment. I could just roll by and pick it up one day.

If you want to check the If the electrodes appear burnt, or the insulator is white ignition timing, refer to the Honda Service Manual. Therefore, the fuel filter Pro Honda HP2 2-stroke oil or its equivalent, sea next larger slow jet is needed.

Remove the alternator cover and keep it handlebar thoroughly, and apply a light coating of all electrical connections. Seat Removal and forward on the seat in each of these areas. Use a stopwatch for consist- or somewhere in the pack. Loosely attach the upper and lower ends of manua Subframe Removal subframe to the mainframe while connecting the 1. Any chance i could get one of those CD’s? Slip the cylinder over the top of the piston while fied torque.



PM me your number or give me directions to your pad thers no point in shipping it. Page 62 Pour the recommended fork oil into the outer tube. Turn the fork damper upside down for 10 minutes and NOTE: Place your CR on the optional Honda work- 4. Install the collars and shroud A bolts. Turn the fuel valve OFF. Warm up the engine.

Rear Suspension Both lighter and heavier than standard springs are available for the shock and fork from your authorized Honda dealer. Fill the fuel tank with pre-mixed fuel page 2. Tighten the lock nut.

Also i have a question, besides the oil to gas mix of Starting The Engine ance by paying extra attention to how you ride during 2.

Page 68 Tighten the fork cap while holding the cut out of the fork Pour the recommended fork oil into the fork damper. Honda White Lithium Grease, or an equivalent, is handy for this because any dirt that penetrates this sealing area will show up clearly. This manual should be considered a permanent part of ,anual motorcycle and should remain with the. Apply oil to the threads and flange surface. Page 2 All information in this publication is based on the latest product information available at the time of approval for printing.