Yamaha Blaster YSF ATV Repair Manual. Yamaha YFS Blaster A Yamaha Blaster ATV repair manual is a book of instructions that blaster choke cable; how to change a carburetor on a yamaha. YFS Service Repair Manual (LIT) – · YFSP YFSG Parts Catalog – · YFSH Parts Catalog –

Author: Taulkree Faet
Country: Monaco
Language: English (Spanish)
Genre: Medical
Published (Last): 21 September 2007
Pages: 483
PDF File Size: 11.85 Mb
ePub File Size: 4.54 Mb
ISBN: 900-8-68417-436-1
Downloads: 66827
Price: Free* [*Free Regsitration Required]
Uploader: Kelabar

Share This Page Tweet. Number of bids and bid amounts may be slightly out of date. EBU Indicates a potential hazard that blaaster result in serious injury or death.

Yamaha Blaster Owners Manual (All Years)

Remove the screws holding the headlight unit assembly to the headlight body. Rear shock absorber 2.

Ride cautiously in unfamiliar areas. We take great pride in our reputation for quality and ex Clymer manual for ”97 Yamaha Blaster.

Fuel tank cap Factory sealed in plastic. Remove the bulb holder cover, turn the If the headlight bulb burns out, replace the bulb bulb holder counterclockwise and remove as follows: EBU Shifting This model has a 6-speed forward transmission. Yamaha dealer if the fuel system needs to be drained instead.

Yamaha Blaster Parts, Service and Owner Manuals – Free Download

I tried to upload them to this site but it didn’t work. Do not ride the ATV if you find Your Yamaha engine has been designed to use any problem with the brakes. I always get a repair manual for each of my toys its nice to save a few bucks on this one. Page 7 Crossing through shallow water.


Rear Shock Absorber Adjustment EBU Rear shock absorber adjustment Never attempt to turn the adjuster beyond The spring preload can be adjusted to suit the the maximum or minimum setting. With manusl lever in yamaua position fuel will not Remove the fuel tank cap by turning it counter- flow.

Wear limit 1 mm 0. There is never a more important glaster in the 1. You will need a computer PC or Mac in order to ownres it and print out the part you need. Page 83 Once you have learned this technique you should be able to perform it at higher speeds or Lean towards Support your in tighter curves. To prevent burns, avoid touching the exhaust system. It represents the result of many years of Yamaha experience in the production of fine sporting, touring, and pacesetting racing machines.

A diagnostic tachometer must be used for this procedure. Lubricate the inner cables and the cable ends. See page Oil quantity: Adjust the headlight beam if necessary.

Table of Contents Add to my manuals Add. Select a large, flat area off-road to become With the engine idling, pull the clutch lever to familiar with your ATV. Never remove any labels from your ATV. Page 92 Avoid hills with excessively slippery or loose surfaces.


All maintenance, service and repair procedures are supported by detailed specifications, photographs, diagrams and exp EdgemxAug 2, Check the slack at the position shown in the figure.


Page 80 Select a large, flat area off-road to become With the engine idling, pull the clutch lever to familiar with your ATV. Make sure that this area disengage the clutch and shift into 1st gear, and is free of obstacles and other riders. Steam cleaning, high- pressure washes, and certain solvents can dam- age these Ownes. You should also wear eye protection goggles or face shieldgloves, boots, long-sleeved shirt or jacket, and long pants. Transmission oil measurement the oil.

You should periodically remove and inspect the spark plug because heat and deposits will cause the spark plug to slowly break down and erode. Page 58 EBU 8 Tie down cargo securely to the carriers.

Full color wiring diagrams – Manual based on actual teardown – Exploded views – Photos, drawings, and charts.

Numbered instructions guide you through every repair procedure step by step. Model YFS Engine oil 2-cycle: Avoid hills with excessively slippery or loose surfaces.

Remove the throttle cable from the throttle 8. Could cause you to react more slowly. The length of the spring changes 1 mm 1. Adjust the spring preload as follows: